
ProPoint PLUS Aspirating Smoke Detectors
1 – 4 Individual detectors per aspirator (providing up to 4 separately identifiable areas); High performance optical ‘Scatter Chamber Detectors’ (SCD); High performance optical ‘Scatter Chamber Detectors’ (SCD) and enhanced CO detection; Multiple language, multi-function LCD display; Simple...
Request a quoteDescription
ProPoint PLUS Optical ‘Smoke’ and ‘Smoke/CO’ detection
Aspirating detection is now a recognised solution for many different fire detection applications. ProPoint PLUS provides up to four separate detectors within a common aspirator enclosure and therefore provides four individually identifiable areas of detection per aspirator.
Each of the four plug-in ‘Scatter Chamber Detectors’ (SCD)’s detector modules can be either ‘optical’ only or combined ‘optical/enhanced CO’ detectors, the CO sensor is only suitable for small room applications. Independent and integrated alarm decision making through the use of complex algorithms extend the range of particle detection, confirm genuine alarms and reduce unwanted alarms.
Installation, configuration and commissioning of ProPoint PLUS detectors is very simple and installer friendly.
Configuration to either Class A, Class B or Class C sensitivity options is achieved through a multi-language, multi-function LCD display without the need for a laptop connection.
Detector set up allows the installer to configure the detector sensitivity to an equivalent setting, as a known number of point type smoke detectors for each Class A, Class B and Class C system. This ensures the system specifier, designer, installer and commissioning engineer configure the ProPoint PLUS SCD’s to the correct sensitivity for the particular application.
Aspirator fan speed and airflow configuration is a also a very simple process allowing ProPoint PLUS aspirating detectors to be installed in a variety of applications with short and relatively long pipe runs.
Technical Specifications
| Airflow Monitoring | ‘High Airflow’ and ‘Low Airflow’ fault monitoring |
|---|---|
| Alarm Indications | Pre-alarm, Fire |
| Application Sampled Air Temperature | -20˚C to 60˚C (-4˚F to 140˚F) |
| Brand | Protec |
| Cable Access | 10 x 20mm knock outs |
| Cable Termination | Screw terminal blocks (0.2 – 2.5mm2, 30 – 12AWG) |
| Current Consumption @ 24VDC, 100% Fan 4 pipe | 580mA quiescent | 620mA alarm |
| Dimensions (mm) | 380(H) x 250(W) x 137(D) |
| Event Log / Data Retention | 24,000 events stored on FIFO basis (alarms, actions, faults and data points) (Approx 30 day historical graph data) |
| Fault Contact | Rated at 30VDC 1A maximum [Normally closed] |
| Humidity | 10 – 93%RH (no icing / non-condensing) |
| IP Rating | IP30 |
| Other Indications | Supply Healthy, General Fault, OLED Display with four navigation buttons |
| Pipe Outer Diameter | 25mm, push to fit tapered inlet |
| Programmable Inputs | 3 monitored inputs that may be configured for Isolate, Reset, Silence, Battery Fault and Mains Fault |
| Programmable Output Contacts | 5 contacts rated 30VDC 1A [Volt-free change over contacts with 28 programming options] |
| Sampling Pipe Network | Number of inlet ports: Up to four Pipe Network Design Tool: ProFlow Maximum pipe length: Specific to individual design. To be compliant to local design codes, and verified by ProFlow. |
| Sensitivity Range | Optical Detection Range: 0.12%obs/m to 11%obs/m Carbon Monoxide Detection Range: 1 to 150 ppm |
| Standards / Approvals | EN 54-17, EN 54-20 AS 7240-20 UKCA CE |
| Supply Voltage | 21 – 28VDC |
| Temperature Range Tested to EN54-20 | -10˚C to 55˚C (32˚F to 131˚F) |
| Threshold Settings Compliant Maximum EN 54-20 | Class A – 15 holes per pipe @ Alarm Level 1.1%obs/m Class B – 15 holes per pipe @ Alarm Level 3.2%obs/m Class C – 15 holes per pipe @ Alarm Level 11.5%obs/m |
| Threshold Settings Recommended Maximum | Class A – 3 holes per pipe @ A1 to A3 Class B – 5 holes per pipe @ B1 to B5 Class C – 8 holes per pipe @ C1 to C8 Class C Escalator Mode – 8 holes per pipe @ ESC1 to ESC8 Class C Prison Mode – PR2 using Sample Head (61-988-00) |
| Weight | 3kg (6.6lbs) |
Documents & Technical Downloads
Aspirating System Solutions
ProPoint PLUS EN54 Tech Sheet
ProPoint PLUS UL/FM Tech Sheet
Product Feature Focus – ProPoint PLUS OPCO – Escalator Mode
Product Feature Focus – ProPoint PLUS OPCO – Prison Mode
Generic Design & Installation Guide
Lift Shaft Design Guide
Atria Design Guide
Warehouse Design Guide
Cold Store Design Guide
Related Products
View Cataloguearrow_forward
Context Plus Smoke detector built in sounder
Indicative Price
from

Simplex 4098-9714 Photoelectric Smoke Detector
Indicative Price
from


